• Tall Walk in Shed• Quick & Easy Assembly • Ridge Reinforced Walls• Wide Double Doors• Available in Various SizesCall us for any missing or damag
6IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.2. Insert the column (COSP) & (COLP) in to corner column fitting and secure with (S1) screws from in
75. Fix the column support (CS) to the column with two (S1) screws.6. Assemble the sliding channel (SLAP & SRAP) together with sliding channel joi
88. Place the sliding channel assembly (SLAP & SRAP) on the top of front column fitting at the both ends.Secure with (S1) screws.9. Insert 4 nos o
911. Place the wall panel (WP2A) on the base bar (BBFP). Line up the holes with base bar.Secure with (S1) Screws.IMPORTANT: USE HAND GLOVES TO PREVENT
10IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.16. Assemble the center band (CB1P) with column fitting (CFP). Secure with (S1) screw at one end.Make 2
11IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.17. Fix the column fitting (CFP) to the front column (COSP) with (S1) screws from inside, fix the other
12IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.Make sure the overlappingposition of panels is asshown in fig. 2.Note20. Place the wall panel (WP1A) on
13IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.Fig.1Fig.2S1S1DCLP321DCLP WP1ASLAPWP1ASLAPDCLPBBFPFig.1Fig.225. Fix the Column fitting (CFP) to the fro
1427. Place the Corner Column fitting (CCFP) on top of the base bar at the back side on both corners. Secure with (S1) screws.Fig.1Fig.2IMPORTANT: USE
Fig.11529. Fix the Column Support (CS) to the columns with two (S1) screws at both corners.30 Place the wall panel (WP3A) on the base bar side (BS2AP)
Duramax Storage ShedLimited Ten Year WarrantyU.S. Polymer Inc. will send a replacement part free of charge, in the event of material defects and or wo
1632. Place the wall panel (WP3A) on the base bar (BS1AP). Line up the holes with base bar and secure with (S1) screws with washer from out side.33. P
17IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.37. Place the top angle side assembly on top of back top angle (ABLAP) and top of sliding channel (SLAP
1840. Secure the Wall Panel to the top angle with (S1) screws.IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.39. Place the top angle side assembly on to
1942. Fix one column fitting with columns to the base bar (BS1AP) with (S1) screws from inside.Fig.1IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.43.
20IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.FrontBack44. Fix two column fitting with column to the base bar (BS2AP) with (S1) screws from inside.S1
2147. Fix the Column fitting (CFP) to the Column with (S1) screw as shown.IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.FrontBackS1CFP48. Fix the Cente
Fig.1Fig.22251. Fix the Center band (CB3P) to the Center band fitting (CBFP) with (S1) screw. See fig.1Fix the other end to the Column fitting (CFP).5
2353. Fix one Column fittings (CBF) with Columns to the other side of base bar (BS2AP) with (S1) screws from inside.54. Place the Wall Panel (WP4A) on
24IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.56. Place the Wall Panel (WP4A) on the base bar side (BS1AP) Line up the holes with base bar and top an
2559. Fix the Center Band (CB3P) to the Column fitting with (S1) Screws. See Fig. 1Fix the other end to the center band fitting (CBFP) with (S1) screw
ACCESSORIESCODE DESCRIPTION QTYFCFP FRONT COLUMN FITTING 2CCFP CORNER COLUMN FITTNG 4CFP COLUMN FITTING 18DCBFP DOOR COLUMN BOTTOM FITTING
2662 Fix the Center Band (CB2P) to the Center Band fitting (CBFP) with (S1) screw . See fig. 1Fix to other end to the Column fitting (CFP) See fig. 26
27IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.65. Place the Wall Panel (WP4A) on the back base bar. Line up the holes with base bar. Secure the Panel
2870. Fix two Column fittings (CBF) with Columns to the back base bar with (S1) screws from inside.IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.S168.
29IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.73. Fix the Center band fitting (CBFP) on the Columns with (S1) screw.71. Place the Wall Panel (WP4A) o
3074. Fix the Column fittings (CFP) to the Column as shown.IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.76. Secure the Panels to the Center bands with
3177. Place the sliding channel cover (SCAP) on sliding channel and secure with (S7) screws at both ends.IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.
32IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.C. RoofParts Needed:(2) Support bracket front right / back left (SB1AP)(2) Support bracket front le
3. Assemble the roof support bracket with Roof support assembly at both ends as shown. Use (S3) bolt & nut.Make 2 SetsS3Fig.1SB1APSB2APFig. 2S333I
34IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.7. Assemble the Support bracket with Roof support assembly as shown. Use (S3) bolt & nut.8. Place t
35IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.9. Place the Facia support right (FSRAP) on top of Roof support as shown. Secure with (S1) screws to su
Exploded ViewIMPORTANT: USE HAND GLOVES TO PREVENT INJURY.RC2PRC2PRC1PRF2APRP4APRF2APRF1APRFSAPRFSAPRS4APFLAPFRAPFRAPFLAPFSLAPSB1APSB4APRS4APSB2APAS1A
36IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.12. Place the Roof Structure (RS4AP) on the top of Roof support and top angle side. Secure with (S1) sc
37IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.16. Place the Facia panel (FLAP) on back side left facia support and fix the Roof plugs with washer and
38IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.18. Place the Roof panel (RP4AP) on top of the Roof support and Facia support. Line up the holes and se
39IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.21. Place the Height Adjustable Support (HAS) to the roof structure (RS2AP) and secure with (S1) screws
40IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.25. Place the Roof panel (RP4AP) on the Roof support and secure with (S1) screws with washers26. Place
41IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.27. Place the Roof panel (RP3AP) by sliding under the Ridge cover (RC1P) to Roof support. Use (S1) scre
42IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.30. Place the ridge cover (RC2P) on top of Roof panel and fix with Roof plugs with washer and drive in
43IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.34. Insert the Roof flashing (RF1AP & RF2AP) under the ridge cover. See fig. 1Line up the holes and
37. Insert the Ridge end cap to the front & back top of the roof and secure with (S1) screws with washer.44IMPORTANT: USE HAND GLOVES TO PREVENT I
45IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.D. Door(1) Door panel (DL1AP)(1) Door panel (DL2AP)(1) Door panel (DR1AP)(1) D
A. Foundation & Base FrameNote: It is important that these instructions are followed step by step.1(2) Foundation ‘U’ Channel (FC1AP)(2) Fou
46IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.1. Assemble the door panel (DR1AP & DR2AP) and Door panel middle support (DMSAP) together with (S3)
47IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.3. Assemble the Door stopper vertical (DSP) to the Door panel (DR2AP) make sure the side edge of the pa
48IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.Fig.15. Assemble the Door panel strip bottom (DSBAP) with Door panel. Make sure the Door panel bottom e
49IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.7. Fix the Door handle (DH) with Door panel from front side with bolt & nut.Left Door Assembly8. As
50IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.9. Place the door panel vertical support (DVSP) to the Door panel (DL1AP) from inside secure the panel
51IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.11. Assemble the Door panel strip top (DSTAP) with Door panel. Make sure the Door panel top edge to be
52IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.13. Assemble to bottom slider (BS) to the Door panel bottom side at both edge with (S3) bolt and nut wi
53IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.15. Slide the Door panel assembly into the base bar front (BBFP). Make sure the bottom slider (BS) shou
54IMPORTANT: USE HAND GLOVES TO PREVENT INJURY.17. Cut the Edging Profile (EDP) to the required length and insert to the Sliding Channel joint (SJP) t
5. Assemble base bar back left (BLAP) and base bar back right (BRAP) with four (S7) screws.See fig. 1 & 2.Fig.1 Fig.2BLAPS7BLAPBRAPTake care of sh
3BLAPBRAPFrontRightLeftBackIMPORTANT: USE HAND GLOVES TO PREVENT INJURY.S18. Insert the base bar side assembly on left side. Insert the edge of (BS2AP
10. Place the base bar (BBFP) on top of base bar side on both side. Secure the with (S7) screw.11. Using the carpenter square, line up the corners.Sec
512. Place the entrance taper channel (ECAP) on top of the (BBFP). Secure with (S1) screws to the foundation. See fig. 1 & 2.BBFPBBFPS1Fig.1 Fig.2
Kommentare zu diesen Handbüchern